Also, Road, you've played with the later test images, check to see if you have a /.norwits file when you boot to the gateway. If you do, remove it, then reboot

/.norwits is a keystone file that triggers the actual install on boot

On Wed, Apr 15, 2020, 12:41 PM Grommish [via Itus Networks Owners Forum] <[hidden email]> wrote:

Because I had been up for a bit and forgot a piece on the first step.

ssh -q -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null [hidden email] "mount /dev/mmcblk0p1 /overlay" 

That'll actually tell it what device to mount to 😁

On Wed, Apr 15, 2020, 9:53 AM Roadrunnere42 [via Itus Networks Owners Forum] <[hidden email]> wrote:

Tried running you instructions but keep getting

mount: can't read '/etc/fstab': No such file or directory

when i running the first command, so I add overlay at the end and all when well

ssh -q -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null [hidden email] "mount /dev/mmcblk0p1 /overlay"

cd into /overlay and saw in image files so went ahead and ran the other commands again all when well, but on reboot and the switch in G mode it still loaded the old gateway image, rebooted several time but still the same, any ideas? what I've done wrong.

Roadrunneruk

On Wed, 15 Apr 2020 at 07:39, Grommish [via Itus Networks Owners Forum] <[hidden email]> wrote:

Itus Shield Firmware v2.0 (OpenWrt SNAPSHOT r11407+1525-54ba15f9fa) ALPHA
NOTE: This WILL erase ALL DATA in the GATEWAY slot!

Download ItusgatewayImage



Instructions to Flash:

Boot into the Shield in whatever mode that you normally use

If you have ssh/scp installed on your PC, you can use it directly.  MAKE SURE YOU ARE IN THE DIRECTORY YOU DOWNLOADED THE FILE INTO!

ssh -q -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null [hidden email] "mount /dev/mmcblk0p1"
ssh -q -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null [hidden email] "cp /overlay/ItusgatewayImage /overlay/ItusgatewayImage-Rescue"
scp -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null ./ItusgatewayImage root@10.10.10.10:/overlay
ssh -q -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null [hidden email] "touch /overlay/ItusgatewayImage"
ssh -q -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null [hidden email] "umount /overlay"

(the flags above just keep SSH/SCP from complaining about the SSH Key for your Shield if it changed.  This way, you don't have to remove the key and re-add a new one)

You MUST ensure that your Shield is in the GATEWAY (OUTER) Position, then reboot

First boot will take a few minutes. The M-LED on the Shield will turn ORANGE when the boot is complete.  

Open 10.10.10.10 and login (no password by default)

Troubleshooting:

If you boot into the new image and you have no IP on eth0:  This happens from time to time, and I'm not sure why.  Reboot the system and let it try again.

Requests:

Suggested changes to the "default" setup are welcome.. Packages, settings, etc.

Running Itus Shield v2 Firmware

---

If you reply to this email, your message will be added to the discussion below:

http://itus.accessinnov.com/FIRMWARE-Itus-Networks-Shield-Firmware-Upgrade-WIP-tp1726p1943.html

To start a new topic under Technical Discussion, email [hidden email]
To unsubscribe from Itus Networks Owners Forum, click here.
NAML

---

If you reply to this email, your message will be added to the discussion below:

http://itus.accessinnov.com/FIRMWARE-Itus-Networks-Shield-Firmware-Upgrade-WIP-tp1726p1946.html

To unsubscribe from [FIRMWARE] Itus Networks Shield Firmware Upgrade *WIP*, click here.
NAML

Running Itus Shield v2 Firmware

---

If you reply to this email, your message will be added to the discussion below:

http://itus.accessinnov.com/FIRMWARE-Itus-Networks-Shield-Firmware-Upgrade-WIP-tp1726p1947.html

To unsubscribe from [FIRMWARE] Itus Networks Shield Firmware Upgrade *WIP*, click here.
NAML

Running Itus Shield v2 Firmware

---

If you reply to this email, your message will be added to the discussion below:

http://itus.accessinnov.com/FIRMWARE-Itus-Networks-Shield-Firmware-Upgrade-WIP-tp1726p1948.html

To start a new topic under Technical Discussion, email [hidden email]
To unsubscribe from Itus Networks Owners Forum, click here.
NAML