[ 0.000000] Linux version 3.10.20 (daniel@Ayoub) (gcc version 4.7.0 (Cavium Inc. Version: SDK_3_1_0_p2 build 34) ) #165 SMP Mon May 18 23:41:17 PDT 2015 [ 0.000000] CVMSEG size: 2 cache lines (256 bytes) [ 0.000000] Cavium Inc. SDK-3.1 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 000d9602 (Cavium Octeon III) [ 0.000000] FPU revision is: 00739600 [ 0.000000] Checking for the multiply/shift bug... no. [ 0.000000] Checking for the daddiu bug... no. [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 000000000c800000 @ 0000000002500000 (usable) [ 0.000000] memory: 0000000000c00000 @ 000000000f200000 (usable) [ 0.000000] memory: 000000002f000000 @ 0000000020000000 (usable) [ 0.000000] memory: 0000000000830000 @ 0000000000100000 (usable) [ 0.000000] memory: 0000000001a00000 @ 0000000000930000 (usable after init) [ 0.000000] Wasting 896 bytes for tracking 16 unused pages [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Using passed Device Tree <8000000000080000>. [ 0.000000] software IO TLB [mem 0x02670000-0x026b0000] (0MB) mapped at [8000000002670000-80000000026affff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x00100000-0xefffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00100000-0x0232ffff] [ 0.000000] node 0: [mem 0x02500000-0x0ecfffff] [ 0.000000] node 0: [mem 0x0f200000-0x0fdfffff] [ 0.000000] node 0: [mem 0x20000000-0x4effffff] [ 0.000000] On node 0 totalpages: 15971 [ 0.000000] DMA32 zone: 14 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 15971 pages, LIFO batch:1 [ 0.000000] Cavium Hotplug: Available coremask 0x0 [ 0.000000] Primary instruction cache 78kB, virtually tagged, 39 way, 16 sets, linesize 128 bytes. [ 0.000000] Primary data cache 32kB, 32-way, 8 sets, linesize 128 bytes. [ 0.000000] Secondary unified cache 512kB, 4-way, 1024 sets, linesize 128 bytes. [ 0.000000] PERCPU: Embedded 1 pages/cpu @8000000002710000 s12544 r8192 d44800 u65536 [ 0.000000] pcpu-alloc: s12544 r8192 d44800 u65536 alloc=1*65536 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 15957 [ 0.000000] Kernel command line: bootoctlinux 0x20000000 numcores=2 serial#=752011191521-36287 console=ttyS0,115200 [ 0.000000] PID hash table entries: 4096 (order: -1, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 4, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 3, 524288 bytes) [ 0.000000] Memory: 983296k/1022144k available (5825k kernel code, 38848k reserved, 2536k data, 26624k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=2. [ 0.000000] NR_IRQS:512 [ 0.000000] CIB interrupt controller probed: 800107000000e000 23 bits [ 0.000000] CIB interrupt controller probed: 800107000000e200 12 bits [ 0.000000] CIB interrupt controller probed: 800107000000e400 6 bits [ 0.000000] CIB interrupt controller probed: 800107000000ec00 15 bits [ 0.000000] CIB interrupt controller probed: 800107000000e600 4 bits [ 0.000000] CIB interrupt controller probed: 800107000000e800 11 bits [ 0.000000] CIB interrupt controller probed: 800107000000e900 11 bits [ 22.422495] Calibrating delay loop (skipped) preset value.. 2000.00 BogoMIPS (lpj=10000000) [ 22.430709] pid_max: default: 32768 minimum: 501 [ 22.435425] Security Framework initialized [ 22.439442] Mount-cache hash table entries: 4096 [ 22.445694] Checking for the daddi bug... no. [ 22.446483] SMP: Booting CPU01 (CoreId 1)... [ 22.450685] CPU revision is: 000d9602 (Cavium Octeon III) [ 22.450688] FPU revision is: 00739600 [ 22.450870] Cpu 1 online [ 22.462285] Brought up 2 CPUs [ 22.465230] Cavium Hotplug: Available coremask 0x0 [ 22.472219] NET: Registered protocol family 16 [ 22.477635] Installing handlers for error tree at: ffffffff808be430 [ 22.495153] PCIe: Initializing port 0 [ 24.557689] PCIe: Link timeout on port 0, probably the slot is empty [ 24.557695] PCIe: Initializing port 1 [ 24.561190] PCIe: Port 1 not in PCIe mode, skipping [ 24.561196] PCIe: Initializing port 2 [ 24.564838] PCIe: Port 2 not in PCIe mode, skipping [ 24.571206] [sched_delayed] sched: RT throttling activated [ 24.584520] bio: create slab at 0 [ 24.588941] vgaarb: loaded [ 24.591871] SCSI subsystem initialized [ 24.595721] libata version 3.00 loaded. [ 24.596138] usbcore: registered new interface driver usbfs [ 24.601571] usbcore: registered new interface driver hub [ 24.606866] usbcore: registered new device driver usb [ 24.612018] pps_core: LinuxPPS API ver. 1 registered [ 24.616816] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 24.626041] PTP clock support registered [ 24.629917] EDAC MC: Ver: 3.0.0 [ 24.633597] PCI host bridge to bus 0000:00 [ 24.637554] pci_bus 0000:00: root bus resource [mem 0x1000000000000] [ 24.643876] pci_bus 0000:00: root bus resource [io 0x0000] [ 24.649444] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 24.657371] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 24.658317] Switching to clocksource OCTEON_CVMCOUNT [ 24.664591] NET: Registered protocol family 2 [ 24.669233] TCP established hash table entries: 8192 (order: 1, 131072 bytes) [ 24.676351] TCP bind hash table entries: 8192 (order: 1, 131072 bytes) [ 24.682840] TCP: Hash tables configured (established 8192 bind 8192) [ 24.689109] TCP: reno registered [ 24.692290] UDP hash table entries: 2048 (order: 0, 65536 bytes) [ 24.698377] UDP-Lite hash table entries: 2048 (order: 0, 65536 bytes) [ 24.705035] NET: Registered protocol family 1 [ 24.709240] PCI: CLS 0 bytes, default 128 [ 26.297738] octeon_pci_console: Console not created. [ 26.302540] /proc/octeon_perf: Octeon performance counter interface loaded [ 26.311401] HugeTLB registered 512 MB page size, pre-allocated 0 pages [ 26.319126] sys_fw_version: 0.1.17 [ 26.319140] sys_revision: 21 [ 26.319489] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 26.325424] NTFS driver 2.1.30 [Flags: R/W]. [ 26.329553] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 26.335687] msgmni has been set to 1920 [ 26.340428] Key type asymmetric registered [ 26.344414] Asymmetric key parser 'x509' registered [ 26.349239] io scheduler noop registered [ 26.353138] io scheduler deadline registered [ 26.357431] io scheduler cfq registered (default) [ 26.362336] octeon_gpio 1070000000800.gpio-controller: OCTEON GPIO [ 26.420153] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 26.427842] 1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 34) is a OCTEON [ 26.435629] console [ttyS0] enabled, bootconsole disabled [ 26.459163] 1180000000c00.serial: ttyS1 at MMIO 0x1180000000c00 (irq = 35) is a OCTEON [ 26.480946] brd: module loaded [ 26.499433] loop: module loaded [ 26.516285] slram: not enough parameters. [ 26.540949] IMQ driver loaded successfully. (numdevs = 16, numqueues = 1) [ 26.560039] Hooking IMQ after NAT on PREROUTING. [ 26.577027] Hooking IMQ before NAT on POSTROUTING. [ 26.596140] libphy: mdio-octeon: probed [ 26.613376] mdio-octeon 1180000001800.mdio: Version 1.0 [ 26.630871] spi_ks8995: Micrel KS8995 Ethernet switch SPI driver version 0.1.1 [ 26.650768] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k [ 26.668757] e1000e: Copyright(c) 1999 - 2013 Intel Corporation. [ 26.687038] octeon-pow-ethernet ERROR: You must specify a broadcast group mask. [ 26.706531] octeon-ethernet 2.0 [ 26.723416] Interface 0 has 4 ports (QSGMII) [ 26.723496] Interface 1 has 4 ports (QSGMII) [ 26.723503] Interface 2 has 4 ports (NPI) [ 26.723517] Interface 3 has 4 ports (LOOP) [ 26.723534] Interface 4 has 1 ports (AGL) [ 26.731462] usbcore: registered new interface driver cdc_ether [ 26.749538] usbcore: registered new interface driver plusb [ 26.767276] usbcore: registered new interface driver sierra_net [ 26.785979] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 26.804802] ehci-pci: EHCI PCI platform driver [ 26.821482] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 26.840417] usbcore: registered new interface driver usb-storage [ 26.858763] usbcore: registered new interface driver usbserial [ 26.876825] usbcore: registered new interface driver usbserial_generic [ 26.895586] usbserial: USB Serial support registered for generic [ 26.913820] usbcore: registered new interface driver sierra [ 26.931606] usbserial: USB Serial support registered for Sierra USB modem [ 26.950799] i2c /dev entries driver [ 26.966814] i2c-octeon 1180000001000.i2c: version 2.5 [ 26.984791] octeon_wdt: Initial granularity 5 Sec [ 27.001890] EDAC DEVICE0: Giving out device to module 'octeon-cpu' controller 'cache': DEV 'octeon_pc_edac' (INTERRUPT) [ 27.024994] EDAC DEVICE1: Giving out device to module 'octeon-l2c' controller 'octeon_l2c_err': DEV 'octeon_l2c_edac' (POLLED) [ 27.048646] octeon_lmc_edac octeon_lmc_edac.0: Disabled (ECC not enabled) [ 29.673361] Netfilter messages via NETLINK v0.30. [ 29.690206] nfnl_acct: registering with nfnetlink. [ 29.707165] nf_conntrack version 0.5.0 (7682 buckets, 30728 max) [ 29.725603] ctnetlink v0.93: registering with nfnetlink. [ 29.743434] xt_time: kernel timezone is -0000 [ 29.759929] ip_set: protocol 6 [ 29.775226] ipip: IPv4 over IPv4 tunneling driver [ 29.792574] gre: GRE over IPv4 demultiplexor driver [ 29.809588] ip_gre: GRE over IPv4 tunneling driver [ 29.827805] ip_tables: (C) 2000-2006 Netfilter Core Team [ 29.845447] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully [ 29.863982] arp_tables: (C) 2002 David S. Miller [ 29.880780] TCP: cubic registered [ 29.896221] Initializing XFRM netlink socket [ 29.912666] NET: Registered protocol family 10 [ 29.932479] mip6: Mobile IPv6 [ 29.947624] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 29.965439] sit: IPv6 over IPv4 tunneling driver [ 29.983544] ip6_gre: GRE over IPv6 tunneling driver [ 30.001247] NET: Registered protocol family 17 [ 30.017865] NET: Registered protocol family 15 [ 30.034520] Bridge firewalling registered [ 30.050671] Ebtables v2.0 registered [ 30.113176] 8021q: 802.1Q VLAN Support v1.8 [ 30.129540] Key type dns_resolver registered [ 30.146071] L2 lock: TLB refill 256 bytes [ 30.162208] L2 lock: General exception 128 bytes [ 30.178946] L2 lock: low-level interrupt 128 bytes [ 30.195857] L2 lock: interrupt 640 bytes [ 30.211906] L2 lock: memcpy 1152 bytes [ 30.229855] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 30.254588] Freeing unused kernel memory: 26624K (ffffffff80930000 - ffffffff82330000) [ 46.706804] mmc1: BKOPS_EN bit is not set [ 46.727493] mmc1: new high speed DDR MMC card at address 0001 [ 46.745962] mmcblk0: mmc1:0001 P1XXXX 3.60 GiB [ 46.762947] mmcblk0boot0: mmc1:0001 P1XXXX partition 1 2.00 MiB [ 46.781315] mmcblk0boot1: mmc1:0001 P1XXXX partition 2 2.00 MiB [ 46.799683] mmcblk0rpmb: mmc1:0001 P1XXXX partition 3 128 KiB [ 46.821599] mmcblk0: p1 p2 p3 p4 [ 46.842558] mmcblk0boot1: unknown partition table [ 46.864070] mmcblk0boot0: unknown partition table [ 47.498180] kjournald starting. Commit interval 5 seconds [ 47.516832] EXT3-fs (mmcblk0p4): using internal journal [ 47.535110] EXT3-fs (mmcblk0p4): recovery complete [ 47.552173] EXT3-fs (mmcblk0p4): mounted filesystem with writeback data mode [ 47.787879] init: failed to symlink /tmp -> /var [ 47.804927] init: Console is alive [ 47.820788] init: - watchdog - [ 48.836923] init: - preinit - [ 52.035967] mount_root: mounting /dev/root [ 52.052931] mount_root: loading kmods from internal overlay [ 52.182371] block: attempting to load /etc/config/fstab [ 52.202020] block: extroot: not configured [ 52.222990] procd: - early - [ 52.238327] procd: - watchdog - [ 52.955181] procd: - ubus - [ 53.970778] procd: - init - [ 55.754624] NET: Registered protocol family 38 [ 55.781254] tun: Universal TUN/TAP device driver, 1.6 [ 55.798605] tun: (C) 1999-2004 Max Krasnyansky [ 55.826692] u32 classifier [ 55.841564] input device check on [ 55.857347] Actions configured [ 55.873995] Mirror/redirect action on [ 55.898573] PPP generic driver version 2.4.2 [ 55.915977] NET: Registered protocol family 24 [ 57.984304] SGMII0: Port 1 link timeout [ 57.984548] eth1: 1000 Mbps Full duplex, port 1 [ 57.984660] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 57.985394] device eth1 entered promiscuous mode [ 57.987452] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 58.015093] eth0: 1000 Mbps Full duplex, port 0 [ 58.015177] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 58.036736] eth2: 1000 Mbps Full duplex, port 2 [ 58.036871] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready [ 58.963355] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 58.963418] br-lan: port 1(eth1) entered forwarding state [ 58.963441] br-lan: port 1(eth1) entered forwarding state [ 58.963490] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 58.993427] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 59.013495] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 60.963183] br-lan: port 1(eth1) entered forwarding state [ 68.012988] eth0: Link down [ 69.007361] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 70.982948] eth1: Link down [ 71.973370] br-lan: port 1(eth1) entered disabled state [ 72.023436] eth0: 1000 Mbps Full duplex, port 0 [ 72.023474] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 74.052940] eth2: Link down [ 74.993266] eth1: 1000 Mbps Full duplex, port 1 [ 74.993309] br-lan: port 1(eth1) entered forwarding state [ 74.993344] br-lan: port 1(eth1) entered forwarding state [ 76.026015] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready [ 76.993168] br-lan: port 1(eth1) entered forwarding state [ 78.053337] eth2: 1000 Mbps Full duplex, port 2 [ 78.057323] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 96.043018] eth0: Link down [ 97.037466] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 98.012943] eth1: Link down [ 99.003376] br-lan: port 1(eth1) entered disabled state [ 99.053432] eth0: 1000 Mbps Full duplex, port 0 [ 99.053463] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 100.092998] eth2: Link down [ 101.023243] eth1: 1000 Mbps Full duplex, port 1 [ 101.023280] br-lan: port 1(eth1) entered forwarding state [ 101.023314] br-lan: port 1(eth1) entered forwarding state [ 102.026988] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready [ 103.023168] br-lan: port 1(eth1) entered forwarding state [ 103.043447] eth2: 1000 Mbps Full duplex, port 2 [ 103.043655] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 122.733175] device eth2 entered promiscuous mode [ 122.873177] device eth0 entered promiscuous mode [ 215.669585] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.